Wednesday, July 30, 2008

Refill Instructions Epson T0781-T0786 refillable ink jet cartridge

Our how-to guide shows the easy fill process of the T0781, T0782, T0783, T0784, T0785 & T0786 ink jet cartridges. Also covers information about the ARC (auto-reset chips) and refilling information.

Instructions on Filling & Refilling Epson Compatible T781, T0782, T0783, T0784, T0785 & T0786 ink jet cartridges with ARC (auto-reset chips).

The refillable cartridges for T0781, T0782, T0783, T0784, T0785 & T0786 contain an auto-reset chip. Once ink level falls to a predetermined level the chip automatically resets to near full capacity.Cartridges have a 10+ml capacity per cartridge.

These cartridges are of a 2 plug design, but not pressure filled as previous 2P cartridges were.One plug is used as a fill hole while the other is a vent plug. The image on the right shows the two plug locations.

Filling & Refilling:

  • Remove clear rubber fill hole plug
  • Fill injector with desired color ink.
  • Insert injector needle into cartridge
  • Slowly inject ink. Make sure you do not push needle all the way to the hub (yellow plastic portion of needle.) Inject ink slowly
  • When completed injecting ink replace original clear fill hole plug.
That is it. Cartridge has now been filled and is ready for use.Though the image to the right shows the cartridge laying on it side this is not recommended. It was taken this way to show the ink in the cartridge. Always keep cartridge upright.

Before attempting to use any cartridge make sure you have ALL cartridges filled.Cartridges do not work independently. The printer will show an error message of only one - five refillable cartridges are installed.

Replace any cartridges already in the printer with a complete set of refillable cartridges.
Once all cartridge have been inserted remove the vent hole plug from the cartridge.The vent hole plug is the color plug. On the image to the right the two leftmost cartridge plugs have been removed.

After removing all six plugs hit the ink cartridge button.Printer will begin to run an initial cartridge prime, the same as when any new cartridge is installed.After prime has been completed run a print test.

IMPORTANT INFORMATION

As with the OEM cartridges, refillable cartridges may not appear on the Epson Print Status window at all times. (image on right). If you open your printer properties window you can see the current status of the ink levels.(image on left of picture). This usually only occurs when running multiple print job without breaks in between.

Once a break in the print occurs your ink level will appear in the Print Status window once again.The ink level not appearing in the Status window is not an aftermarket related issue, but a printer related issue. This occurs on both OEM cartridges as well as aftermarket.

Never install less than 6 refillable cartridges at one time. Printer will not recognize the Epson cartridges when one of the refillable are installed.

Cartridge Chip auto-reset

These cartridges will reset automatically. There is no hitting cartridge change button or turning printer on and off required. Cartridge will all auto-reset at same time. It is advised that all cartridges be refilled at this time to prevent any cartridge running out of ink.Some cartridge may contain a good deal more ink than others depending on the first cartridge that requires reset. In most cases this is black. (under testing of 5 sets using of cartridges on 1 each R260, R380 & RX580).

Refilling

After initial fill when you are ready to refill return allplugs back to cartridge. Remove cartridges from printer and repeat fill process. There is no difference in refill from the initial fill.

Saturday, July 26, 2008

The Secret Resetter Code for Canon S9000



1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.

Your printer should respond as normal.

The Secret Resetter Code for Canon MPC190
Reset Waste Ink

1. Enter SERVICE MODE.
By pressing Menu Copy Scan Copy Copy
2. Select TEST MODE.
3. Select [8] PRINTER TEST in TEST MODE.
4. Select 3. [EEPROM CLEAR].
5. Select 0. [INK COUNT].
6. Press the [Set] key.
7. Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Friday, July 25, 2008

The Secret Resetter Code for Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520



1. Turn off the printer.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
4. You are now in Service mode.
5. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
(a). service/factory test printout, including ink sensor check
(b). EEPROM info printout
(c). EEPROM initialization
(d). Clear the waste-ink counter
(e). Printer model setting. (more selections beyond this- leave this alone)
6. After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta

The Secret Resetter Code for Canon BJ-30 BJC-35v BJC-70
F14 Error Reset

1. Unplug adapter
2. Hold POWER
3. Plug in ADAPTER
4. Release POWER after printer starts
5. Hold FF and MENU and press POWER
6. Release after beeps
7. Press <> Cartridge until 1A is displayed
8. Press ONLINE
9. Press POWER to shutoff printer
10. Unplug printer then re-plug printer

Thursday, July 24, 2008

The Secret Resetter Code for Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620 Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500



1. Power off printer
2. Hold Resume button then press and hold POWER, the beeper will sound once.
3. Hold POWER and release RESUME
4. Press RESUME twice
5. When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6. Press Power to set data

The Secret Resetter Code for Canon BJC-600 BJC-600e BJC-610 BJC-620

1. Unplug Power Cord
2. Hold POWER and FF and Print Mode buttons
3. Plug in Power Cord
4. Release after the beeps

The Secret Resetter Code for Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70

1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons after the printers starts up
5. Hold CARTRIDGE and RESUME
6. Press POWER
7. Release all buttons after the beeps
8. Press CARTRIDGE 16 times
9. Press RESUME
10. Unplug the Power cord

The Secret Resetter Code for Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA IP3000 above



1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Wednesday, July 23, 2008

The Secret Resetter Code for Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265 Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650



1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5. Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME

The Secret Resetter Code for Canon BJC-5000

1. Power off printer
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
5. Press Power to set data

Service Test Print

1. Power off printer
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME 2 times. The indicator should be GREEN.
5. Press Power to Print

Nozzle Print

1. Power off printer
2. Press and POWER, until the printer beeps and release.

Demonstration Print

* While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

The Secret Resetter Code for Canon BJC-5100
Self Test

* Switch Printer off. Hold Power for 1 beep.

Waste Counter Reset

1. Power off printer
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME 4 times. The indicator should be GREEN.
5. Press Power to set data

Service Test Print

1. Power off printer
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME 2 times. The indicator should be GREEN.
5. Press Power to Print

Nozzle Print

1. Power off printer
2. Press and POWER, until the printer beeps and release.

Demonstration Print

* While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

Tuesday, July 22, 2008

he Secret Resetter Code for Canon BJC 1000 Serie



1. Remove Cartridge
2. Unplug the AC Power Cord
3. Hold down the RESUME button
4. Release RESUME after plugging in the AC Power cord.
5. Press the RESUME once within 5 seconds and release the RESUME .
6. Press and HOLD RESUME for two seconds or more and release it.
7. Press and HOLD RESUME for two seconds or more and release it.
8. Unplug AC Power Cord to set data.

Monday, July 21, 2008

The Secret Resetter Code for Canon S450 Printer



1. Power off printer
2. Hold Resume button then press and hold POWER, the beeper will sound once.
3. Hold POWER and release RESUME
4. Press RESUME twice
5. Release Power button
6. When the indicator lights steady, press RESUME 3 times. The indicator should be orange.
7. Press Power to set data

The Secret Resetter Code for Canon BJC-2000 BJC-2100 Serie

1. Remove the Cartridge
2. Unplug the AC Power Cord
3. Close Front access panel
4. Hold down the RESUME/RESET button and plug in the AC power cord
5. Release RESUME/RESET after plugging in the AC Power cord.
6. Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET.
7. Press and HOLD RESUME/RESET for two seconds or more and release it.
8. Press and HOLD RESUME/RESET for two seconds or more and release it.
9. Unplug AC Power Cord to set data.

Sunday, July 20, 2008

The Secret Resetter Code for Canon i320, i255



Waste Ink Counter Reset.
Step 1 : Manual Temporary

1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

or Step 1: Manual Temporary

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2. Open General Tools software and select (USB PORT)
3. Choose (SET DESTINATION 1) And it should be reset.

Remark “After service mode Pls use software for permanent reset”

Saturday, July 19, 2008

The Secret Resetter Code for Canon i850, i950, S600



Start with the printer OFF

1. Hold down RESUME and then hold down POWER
2. Release RESUME
3. Press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter
Blog Free Epson Resetter download, Epson Driver Download , epson printer software, epson dot matrix printer, epson inkjet cartridge, Epson Maintenance Service and Repair utility