Wednesday, January 21, 2009

Resetting cartridge Epson R290


When I have trouble on my cartridge R290, is currently the forum's neighbors.
Hopefully it can help you .
The original cartridge of R290 havechip system that calculates the number of print-out that we already do, after reaching the maximum limit will require the replacement of the printer cartridge.
This also happens on the system infus R290, infus implement this system combine the chip, which is equipped with a switch / switch on the top of the cartridge.
Function of this switch is to reset the volume of the print cartridge if the replacement cartridge is required, meaning we R290 printer "deceit" as if we have to change with a new cartridge.

Note: almost all types of printers epson latest chip I use it is difficult to be modified, with different types such as the previous R230, R250, C67, etc., which can be reset to its done in auto, for the latest types of reset is done with the help of user / users.

Here's How to reset cartridge R290:

(The need to reset the printer cartridge, printer will give you a warning, a light red / orange blink-blink in the reset button (on the power button)).
Open the printer cover
Remove the paper / material feed sensor cover,
Press the reset (the power button) several times (1-3x), to the position of the cartridge in the position of the replacement cartridge (right),
Pejet button switch on the cartridge (rather long), then release,
pairs back penyumpal paper sensor cover
close the back cover printer
press reset button again, the printer reacts to give voice to the paper I draw a very long time,
the printer is ready for use again,
The way above will be done each time the printer requires replacement cartridge, which is marked with a light reset blink-blink red / orange.

this is the resetter.
Resetter R290 Download

It’s FREE.

Good luck

Resetter Printer Epson CX7300



1. Switch on printer
2. Download Adjustment program Epson
2. Open auto.bat to set the date to 17 January 2006
3. Run adjprog.exe
4. Click accept
5. Click particular adjustment mode
6. Go to maintenance then Select waste ink pad counter then click ok
7. Click on "check button till its done then click on initialization button
then click on finish button
8. Switch off printer for 5 secs then switch on again
9. After you reset succesfully, you can change the date back to normal

Epson Nozzle Clogs

Cleaning kit usage:

Guidelines for most epson printers :

But I think it is due to the following work method :

BIGGEST REMARKS :
-BE PATIENT !!!
-DO NOT LET AIR GET INTO THE INKTUBES OF YOUR PRINTER !!!
(this is why you need to prepare the syringe)

Phase 1 : Syringe preparation
1.Fill up the syringe COMPLETELY with the cleaning solution
2.Putt the little tube on the syringe
3.Push the fluid gently till it drops out the tube. (so that no air gets into the ink tube of the printer).

Phase 2 : Printer preparation
1.Make sure you have full ORIGINAL epson ink cartridges for your printer at your disposal.
2.Disconnect the printer from the pc
3.Connect your printer to the power cable.
4.Push the power button on the printer ,and once the inktray starts moving to the cleaning cycle remove the power cable.
5.Now you can move the inktray by hand. Move it to the position which enables you to open it.
6.Open the inktray ,remove the color of the cartridge you whish to clean.Then close it.
7.Now move the inktray gently to the right (not completely) until you have space to put a small paper towel underneath.The put the paper towel underneath. Then slide it back to the left so it's above the paper towel.
8.Now put connect the syringe (with the little tube) on the inktube.
9.Gently push the cleaning fluid into the the inktube. (the complete 1.0 ml)
10.Fill up the syringe again ,and repeat step 8,9 .
11.IMPORTANT : Don't remove the syringe ,let on the ink tube.
12.Wait for 2h

Phase 3 : Finishing
1.Remove the syringe (and the small tube).
2.Put the inkcartridge back and close the inktray.
3.Slide the inktray to the right and remove the paper towel.
4.Connect the power to the printer.
5.Connect the printer to the pc and start the printer
6.From the printdriversettings ,run the cleaning of your heads 3 times.
7.Now print at least 15 testpages.

If after phase 1,2 and 3 your printer is still not working correctly , -test page not ok- then just repeat phase 1,2 and 3 again.

In order to avoid such problems ,just print at least 1 test page every week. I had my first epson inkjet printer for 6 years and no problems.
So whoever is using an epson printer :
-use original epson ink
-print at least 1 test page a week
-NEVER let the printer without a cartridge inserted (full or empty)

SSC SERVICE UTILITY

I hope this helps some of you who are frustrated and ready to throw out your Epson printer
Problems with my Epson printer, the red and green light began flashing and a window popped up, saying, take it to your services center because some parts have reached the end of their life.
Printer companies set a “protection counter” on all printers , it’s an internal counter measuring the amount of ink wasted by head cleaning.


Reset the "protection counter" as well as clean the “waste ink pad overflow”.

1. Unplug the power and USB cables from the printer. Pry open the printer,
careful not to break anything. Use a flat blade screwdriver to pry it apart;
there are two-three tabs at the back and two at the front. Gently push them in,
and then using a bit of force pry apart the cover.
2. Next remove the two (2) waste ink pads.
They are located at the back on the left hand side. I used the flat blade
screwdriver to lift up the ink pads (they were soaked).
Please use rubber gloves as it gets very messy.
3. Next wash them with just plain hot water until they are white again.
I just let the hot water run on them (the pads are about three inches long).

4. Once washed dry them using a hair drier. (you could place it the sun for
a few hours or on top of your heater or maybe in a heated oven; (make sure you do
not set it on fire with too much heat).
5. Once dried place the pads back in the ink waste bin at the back of the printer.
6. Closed the printer cover and put back all the pieces and plug in the USB
& power cable and turned it on. (Yes the lights are still flashing).
7. Go to this link and download this software: SSC Download

8. Install the software and run it.
9. Select your printer and model number. It will ask if you replaced with new pads;
say “YES”. Then close the window.
10. Now right click on the SSC service utility, it looks like
a printer icon near your clock in the task bar.
11. Then click on reset counters. You can do all other stuff with this utility too.
12. Turn off the printer power and then turn it on again.
If necessary un-plug the power cord from the back of the printer,
wait 20 seconds. Plug it back in.
13. IT WORKS AGAIN.

Friday, January 16, 2009

Inkjet Printers Epson Stylus T11




This printer is cheap but high-resolution support. Suitable for home users and the lovers photographi. Because, other than the results of the high-molder also molder lasting results.

Printer's target this segment of the home have the highest resolution in the class, which can reach 5760x1440 with Variable-sized Droplet Technology. By using the technology, Epson T11 able to produce a text that is more sharply, the more beautiful colors and prints of the results of a more durable.

Ink default printer features Epson Durabrite Ultra Link, and pulling the ink in the design in such a way so resistant to water and mold can not make the results quickly terdegradasi. In this case, the Epson picking cetakkannya that the results remain sharp and beautiful for many years.

Not to burden the users in terms of the cost of replacing the cartridge, the stylus T11 has also features sparingly with the Epson INKdividual Cartridges for Maximum Savings. Where each cartridge is inserted independent. Which means that, if a certain color cartridge out, so users only need to replace the cartridge out of it. This is of course more cost-efficient compared to a combined cartridge, which must replace the color cartridge 1 still contains the other.

Epson Stylus T11 mempu print speed with 22 page document didn't per minute and 33 color pages to the document. Meanwhile, to print the photos needed time 156 seconds, to the size of 10x15cm or 4x6 inch borderless with a maximum resolution. The results of mold tray can hold up to 80 sheets of paper A4

In it, the software is also available from Epson Perfection Photo Creativity Suite. This software can mongkustomisasi images in which you want to print. So users do not need to look more photo-processing software daro third parties. With this software, users can get results than a photo lab printing photos. For not caused, Epson PhotoEnhance can also automatically to Adjust the picture to a photo image will be printed in color have a more beautiful color.

Epson Stylus T11 berdimensi 435x219x165mm with a weight of 2.8 kg. The operating system didukungnya is Windows 2000, XP, 32 and 64 bit and Windows Vista. For Macintosh users can use the operating system MacOS 10.3.9 to the top of the series. When the printer work requires power only 11 watts.

adjustment program epson stylus
free download
Blog Free Epson Resetter download, Epson Driver Download , epson printer software, epson dot matrix printer, epson inkjet cartridge, Epson Maintenance Service and Repair utility